Page 173 - USAG2021

485
493 A
Clutch disk aligner
- Supplied with three expansion pliers 485 R (A-B-C) Two-ply webslings
- Safety coefficient 7:1
- Combination of colours and raising power according to
capacity Cod. Q.tà x conf. €
a
mm code the norms EN 1492-1
14,5÷25 U04856001 1
power max L code Q.tà x conf. €
Cod.
a
ton m
1 2 U04930002 1
1 3 U04930003 1
485 R 1 4 U04930004 1
1 5 U04930005 1
Spare expansion pliers 1 6 U04930006 1
- For clutch disk aligner 485 2 2 2 3 U04930012 1 1
U04930013
2 4 U04930014 1
a
n° capacity Cod. Q.tà x conf. € 2 5 U04930015 1
code
mm 2 6 U04930016 1
A 14,5÷18 U04850003 1 3 2 U04930022 1
B 18÷21 U04850004 1 3 3 U04930023 1
C 22÷25 U04850005 1 3 4 U04930024 1
472 N 3 5 U04930025 1
3 6 U04930026 1
Bar-type pullers for separators
- Model with sliding legs for use in combination with
separators 472 AN
- Supplied with two Chrome plated inserts, nuts and
washers
- Special Chrome Molybdenum steel pression screws
- Special Silicon-Manganese steel body 490
- Chrome plated finish 493 B
- Spare inserts: Nut splitters Roundslings
n°1: U.53R1L - For splitting and removing seized nuts without damaging
n°2: U.53R2L the screws - Structure with wear resistant sheath
n°3: U.53R3L - Carbon steel wedge - Safety coefficient 7:1
n°4-5: U.53R4LA - Special Chrome Vanadium steel body - Combination of colours and raising power according to
- Chrome plated and burnished finish the norms EN 1492-2
power max L code Q.tà x conf. €
Cod.
a
a
n° a b c d e L code Q.tà x conf. € n° W a O Cod. Q.tà x conf. € ton m
a
Cod.
code
mm mm mm mm mm mm mm mm mm 1 1 U04930052 1
1 40÷110 180 M10 11 M16 135 U04720001 1 1 5÷10 22 12 U04900001 2 1 1,5 U04930053 1
2 70÷200 240 M16 11 M16 220 U04720002 1 2 8÷16 30 14 U04900002 2 1 2 U04930054 1
3 75÷280 300 M20 21 M27 320 U04720003 1 3 16÷24 45 19 U04900003 2 1 2,5 U04930055 1
4-5 145÷400 350 M22 25 M33 450 U04720004 1 4 19÷27 57 21 U04900004 2 1 3 U04930056 1
2 1 U04930062 1
2 1,5 U04930063 1
Bearing separators 472 AN fit behind the part to be pulled out, 2 2 U04930064 1
when the jaw ends of conventional pullers cannot pass. 2 2,5 U04930065 1
2 3 U04930066 1
3 1 U04930072 1
3 1,5 U04930073 1
3 2 U04930074 1
• The wedge-shaped jaws close and separate the piece using 3 2,5 U04930075 1
the back surface as support base. 3 3 U04930076 1
• The separators are used with mechanical screw pullers or with
pullers specially developed for use with manual jacks with
hydraulic mechanism.
Mechanical
screw SAFETY
separator For extractions with separators 493 C

and puller and pullers do not use impact Anchorage belt
wrenches. - Belt width 35÷50 mm
- Ratchet-type tensioner 35÷50 mm
- Anchorage charge 1000÷2000 N
- Hook for codes U04930102, U04930103, U04930104
- Double hook for code U04930106
Separator and puller with manual - Reference norm EN 12195-2
hydraulic assistance
L
a
Cod.
• Puller used with 466 N hydraulic jack mm x m load code Q.tà x conf. €
N
• To be used only with pullers and separators 35x4 1000 U04930102 1
472 AN (4-5) and 472 N (4-5) 35x6 1000 U04930103 1 1
50x8
2000
U04930104
50x10 2000 U04930106 1
171